Skip to main content

MEO Class 4

Safety: 
  • Gmdss, EPERB how to activate eperb manually & automatically 
  • LSA code ism SMS 
  • Marpol annexe with date 
  • Solas chapter & apply to which ship 
  • Emg. dg & emg. fire pp regulations 
  • Pounding panting tender stiff ship 
  • Arrangements for panting n pounding
  • Bwm 
  • what is chamber 
  • solas regulations for life raft all
  • Name all annexe and explain annexe 6 (everything)
  • overhead crane safties
  • Name all motions of crane
  • length between perpendicular? at what length it cuts rudder stock
  • IG safeties 
  • draw Deck seal 
  • CO2 release if you are in Port and the Captain orders you to do, what will you do, (No timer and all, fully manual)
  • Scavenge box temperature rise
  • Precautions for scavenge inspection after a scavenge fire
  • STCW chapters 
  • what are the requirements for working hours?
  • Under what conditions you wouldn't hand over the watch. 
  • CO2 FF discharge criteria
  • Marpol Annex 6 controlled emissions.
  • where do Nox and Sox come from
  • Name the ECA.
  • What is the sulphur limit coming from 2020
  • Angle of LOL
  • Freeboard, why
  • Loadline
  • Deckline- Margin Line
Motor:
  • Defects in Liner - explain all
  • Why Cover Leafing and diagram
  • Hydrophore cut in cut off - why checks will u do
  • Thin Shell bearing layers and it's advantages.
  • Purpose of the flash layer
  • What is the fuel pump lead and how to measure?
  • How to float and set economiser safety valve
  • Purpose of tie rod
  • Tie rod loose- how will u come to know 
  • Tie rod tightening procedure
  • Overhauling of Pressure Jet Burner and checks
  • How will u set distance between electrodes and what tool will u use
  • Types of Welding
  • Explain MIG welding 
  • Shielding gas for MIG welding 
  • Defects in welding 
  • Welding Position 
  • Boiler Water Test
  • What will be your action if all the test results are beyond the range
  • During watch, u find Oil in Hotwell- what will be your action (where it is coming from and how will u remove it)
  • Purifier shaft height n not getting rpm 
  • Boiler accumulation test n why it done? 
  • Boiler water test limit of ppm if exceeded action
  • Fwg vacuum loss reason n salinity increase
  • Gear pump overhaul NPSH centrifugal pump diagram n its charastics 
  • Manual purging of boiler n firing 
  • Valve Timing diagram of 2S engine
  • Why fuel injection earlier, fuel property.
  • how would u know if air start valve is leaking, precautions? 
  •  Crankcase Inspection 
  •  Fuel injector overhaul, All four tests.
  • Then he asked about what do u do before fitting the copper gasket ( he said annealing )
MEP:
  • How to order bolt?
  • How to bend copper pipe small dia at 90° 
  • How to fixed two different dia pipe 
  • Pipeline testing 
  • Copper pipe cutting tool n it's material
  • what is bending machine, how it works
  • how to bend copper pipe
  • how to order bolt
  • what type of bolts fitted on a pump
  • how to replace leaking piece in 2mm Internal dia copper pipe ( cold process) 
  • Extracting a broken stud... flushed on the surface.
  • Purifier and clarifier difference 
  • Air Compressor safeties
  • Refrigeration Cold chamber temp. Not maintaining
  • Boiler gauge glass blowdown
  • Opening sequence of Manhole doors and why? Shape and alignment?

Electrical:
  • Msb & ESB safety
  • Motor not staring 
  • Steering gear regulations n safety of motor
  • Avr 
  • Under voltage overload trip how daspot work 
  • Open ckt short ckt 
  • Earthing n founding it's foult1. safety precautions while working on electric equipment
  • what are losses 
  • checks before connecting shore connection
  • total blackout recovery procedure 
  • generator maintenance
  • Full wave rectifier, Draw and explain. Advantage.
  • What batteries you had on ship?
  • Battery room entry safeties
  • why vent, what happens otherwise 
  • Values of specific gravity
  • how would u measure 
  • photoelectric cell? Where all do u use on ship?
  • Purpose of the flame eye?


Labels:

Comments

Post a Comment

Popular posts from this blog

Bilge Injection Valve

Bilge Injection is a valve that enables the engine room bilges to be pumped out directly overboard in the event of an emergency such as flooding. The valve is normally fitted to the end of a branch connection with the main sea water suction line. This enables large main seawater cooling pumps to be used as a bilge pump in an emergency. Emergencies like fire and flooding involve the use of seawater. If there is a fire, seawater is the biggest resource of water available in the sea. Similarly, if it involves flooding of the engine room, cargo spaces or any other place on the ship for that matter; you would again require pumping the sea water out of the ship. In both these cases, you require pumps.  There are two valves in close proximity namely main injection valve and bilge injection valve. Both of them have their own independent controls. The diameter of the bilge injection valve is kept nearly 66% of the main valve diameter which draws water directly from the sea th...
Post a Comment
Read more

Difference Between A, B & C-Class Divisions?

IMO Symbol A Class Division  IMO Symbol B Class Division  SOLAS has tables for structural fire protection requirement of bulkheads and decks. The requirements depend on the spaces in question and are different for passenger ships and cargo ships. The Administration has required a test of a prototype bulkhead or deck in accordance with the Fire Test Procedures Code to ensure that it meets the above requirements for integrity and temperature rise. Types of Divisions: "A" Class "B" Class "C" Class "A" Class: "A" class divisions are those divisions formed by bulkheads and decks which comply with the following criteria: They are constructed of steel or equivalent material They are suitably stiffened They are constructed as to be capable of preventing the passage of smoke and flame to the end of the one-hour standard fire test. they are insulated with approved non-combustible materials such that the average tempera...
14 comments
Read more

Why do we blow through engine before starting ?

The engine is blown through on air before starting it : a) To Blow out through indicator cock any residual exhaust gas or     other products of combustion trapped inside the cylinder after     shutting the engine. b) To check if any jacket cooling water from cylinder head or     turbocharger or any other source, has leaked while the engine          was shut and collected on top of piston. If while blowing                  through, water comes out of indicator cock or relief valve, we          need to investigate and rectify the fault before starting the                engine. It is imperative that the engine is blown through before        starting. There have been cases where the generator engine has        been started from control room without bothering to blow     th...
13 comments
Read more