Skip to main content

MEO Class 2

Safety:
  • IEEC certificate under which annexure and chapter, validity
  • Required eedi, attained eedi with formula
  • MLC Certificate and port state inspection why came in force in2013, not 2006 .no of article in it.
  • Dynamic test of lifeboat.
  • Maintenance of centrifugal brake as 2nd engineer, no of brake.
  • NOx technical file content. 
  • Maintenance of portable fire extinguishers as per DG shipping.
  • In the container ship, there are some box tell me the name of all.
  • Sopep , what information , why provided , who approves???
  • why mild steel used for ship building , carbon %, difference between strength & hardness
  • Instantaneous rate of discharge
  • Precaution during inclining experiment.
  • Annexe 3
  • Reception facilities
  • Propeller pitch ratio.
  • Centre of floatation.
  • Safeties for bulk carrier
  • About high density cargo loading
  • What are all the rules regarding triangle marking on bulkcarrier loading high density cargo...wheater applicable to all types of bulk carrier loading high density cargo?
  • Chapter 9 objective
  • Ism applicable to what kind of ships?
  • How many chapters in ism
  • Inclining experiment..why and how...where u will place
  • Co2 calculation with units ...what is free volume of co2
  • How rudder is fitted

Motor:
  • Relation between speed and mcr and cross questions
  • Volute casing and centrifugal pump working
  • Main engine reversing
  • Venturi effect and its principle
  • How does automatic start air valve work, where does it get signal from.
  • Alfa lubricator MCU, input signal (crank angle, rpm and load index) and output (he said 2 signal one is alarm and other. I said signal for opening solenoid vv. He didn't agree.)
  • Stainless steel Aluminium, Chromium, Silicon, Manganese % and use.
  • Lub oil additive
  • Pour point
  • Stresses in crosshesd bearing
  • Crankshaft material
  • Humidity control
  • Boiler feed water line diag
  • Nox reduction technique

MEP:
  • Chain drive tightening procedure
  • Exhaust valve overhauling and measurements
  • Propeller drop
  • Boiler water treatment objectives , chemicals used and composition
  • Main engine holding down bolts, found loose. How to secure the process.
  • Oil in both gauge glass, steps.
  • How to do fuel pump in AE if all flywheel marks are lost.
  • What is the pipe schedule?
  • In a 2 turbocharger system, how to separate one if one is damage. He wanted complete procedure.
  • ER checks as 2/E before leaving Drydock
  • Gate valve not working what to do.
  • Running gear inspection of a.e.


Electrical:
  • What precaution before taking shore supply ?? Donot say phase sequence & voltage he wanted to listen precaution before taking shore supply
  • all gen offload, earthing wire connection & shore connection insulation certificate check
  • what is dielectric? where used physical significance
  • how earth lamp works which principle ??
  • how to determine where earth fault occur ?
  • Battery condition how to check ??
  • Trickle charging, why its done ,why self discharging.
  • Induction motor advantages.
  • hysteresis loss in the transformer.
  • enclosed in pump room of tanker1. How to adjust current during welding.
  • Leakage between tube and tube plate how to repair.
  • Earth fault ...how will u know an earth fault occurs...how earth fault indicators working(both meter and lamp working)
  • Preferential trip why how it works...if overload still exist what will happen...how various time delays are achvied
  • Black out what will u do..how emergency generator starts...how battery came in to operation in transom period?
  • Shaft earthing...why...how?

Labels:

Comments

Post a Comment

Popular posts from this blog

Difference Between A, B & C-Class Divisions?

IMO Symbol A Class Division  IMO Symbol B Class Division  SOLAS has tables for structural fire protection requirement of bulkheads and decks. The requirements depend on the spaces in question and are different for passenger ships and cargo ships. The Administration has required a test of a prototype bulkhead or deck in accordance with the Fire Test Procedures Code to ensure that it meets the above requirements for integrity and temperature rise. Types of Divisions: "A" Class "B" Class "C" Class "A" Class: "A" class divisions are those divisions formed by bulkheads and decks which comply with the following criteria: They are constructed of steel or equivalent material They are suitably stiffened They are constructed as to be capable of preventing the passage of smoke and flame to the end of the one-hour standard fire test. they are insulated with approved non-combustible materials such that the average tempera...
14 comments
Read more

Bilge Injection Valve

Bilge Injection is a valve that enables the engine room bilges to be pumped out directly overboard in the event of an emergency such as flooding. The valve is normally fitted to the end of a branch connection with the main sea water suction line. This enables large main seawater cooling pumps to be used as a bilge pump in an emergency. Emergencies like fire and flooding involve the use of seawater. If there is a fire, seawater is the biggest resource of water available in the sea. Similarly, if it involves flooding of the engine room, cargo spaces or any other place on the ship for that matter; you would again require pumping the sea water out of the ship. In both these cases, you require pumps.  There are two valves in close proximity namely main injection valve and bilge injection valve. Both of them have their own independent controls. The diameter of the bilge injection valve is kept nearly 66% of the main valve diameter which draws water directly from the sea th...
Post a Comment
Read more

Why do we blow through engine before starting ?

The engine is blown through on air before starting it : a) To Blow out through indicator cock any residual exhaust gas or     other products of combustion trapped inside the cylinder after     shutting the engine. b) To check if any jacket cooling water from cylinder head or     turbocharger or any other source, has leaked while the engine          was shut and collected on top of piston. If while blowing                  through, water comes out of indicator cock or relief valve, we          need to investigate and rectify the fault before starting the                engine. It is imperative that the engine is blown through before        starting. There have been cases where the generator engine has        been started from control room without bothering to blow     th...
13 comments
Read more