Skip to main content

MEO Class 1

  • if a crew goes for joining a ship ,falls sick before joining,who will take care of him ?
  • definition of major non conformity
  • define inventory management, without using word inventory and management
  • what is new in Solas . Structural requirement for polar ships .what is polar water .what is special in those areas
  • duty of care ? ( Whose duty is it ?)
  • EEOI ,action as c/e to improve .how shaft generator improves waste heat recovery .
  • You have given notice to company to remove 2/e .comapny is not able to do till next port .what will you do ?
  • definition of superstructure .
  • most important quality of Junior you will assess,whom you have prepared for emergency situation.
  • How you as a CE will take over a vessel from outgoing CE
  • DD preparation
  • MLC in context of motivation
  • Heavy running of Propeller. How will you decide that it is happening ?
  • Casualty Investigation code
  • Optimum order quantity ( in spares)
  • How would you develop PMS onboard a new ship ?
  • PSC responsibility as per MLC
  • steering gear beakdown your action.cross questions.pulling a vessel is which type of operation.
  • how you will order tugs
  • Bunker order procedure and cross questions
  • type of leaderships, what type of leader i want to be and why
  • new liner and new piston ring what is the procedure
  • How will you go about fitting BW related equipment on board
  • Shipowner adv in MLC
  • LD Clause (liquidity damage clause)
  • CLC and related
  • C.S deflection and related,
  • When charterer want to go for bareboat CH, not shipowner
  • ABC and VED inventory management
  • Prop curve and related

Labels:

Comments

Post a Comment

Popular posts from this blog

Difference Between A, B & C-Class Divisions?

IMO Symbol A Class Division  IMO Symbol B Class Division  SOLAS has tables for structural fire protection requirement of bulkheads and decks. The requirements depend on the spaces in question and are different for passenger ships and cargo ships. The Administration has required a test of a prototype bulkhead or deck in accordance with the Fire Test Procedures Code to ensure that it meets the above requirements for integrity and temperature rise. Types of Divisions: "A" Class "B" Class "C" Class "A" Class: "A" class divisions are those divisions formed by bulkheads and decks which comply with the following criteria: They are constructed of steel or equivalent material They are suitably stiffened They are constructed as to be capable of preventing the passage of smoke and flame to the end of the one-hour standard fire test. they are insulated with approved non-combustible materials such that the average tempera
14 comments
Read more

Bilge Injection Valve

Bilge Injection is a valve that enables the engine room bilges to be pumped out directly overboard in the event of an emergency such as flooding. The valve is normally fitted to the end of a branch connection with the main sea water suction line. This enables large main seawater cooling pumps to be used as a bilge pump in an emergency. Emergencies like fire and flooding involve the use of seawater. If there is a fire, seawater is the biggest resource of water available in the sea. Similarly, if it involves flooding of the engine room, cargo spaces or any other place on the ship for that matter; you would again require pumping the sea water out of the ship. In both these cases, you require pumps.  There are two valves in close proximity namely main injection valve and bilge injection valve. Both of them have their own independent controls. The diameter of the bilge injection valve is kept nearly 66% of the main valve diameter which draws water directly from the sea through the
Post a Comment
Read more

Load Line & Why it is Important

Merchant ships have a marking on their hull know as the Plimsoll line or the Plimsoll mark, which indicates the limit until which ships can be loaded with enough cargo, internationally, the Plimsoll line on a ship is officially referred to as the international load line. Every type of ship has a different level of floating and the Plimsoll line on a ship generally varies from one vessel to another.  All vessels of 24 meters and more are required to have this Load line marking at the centre position of the length of summer load water line. There are two types of Load line markings:- Standard Load Line marking – This is applicable to all types of vessels. Timber Load Line Markings – This is applicable to vessels carrying timber cargo. These marks shall be punched on the surface of the hull making it visible even if the ship side paint fades out. The marks shall again be painted with white or yellow colour on a dark background/black on a light background.  The comp
15 comments
Read more